Floor Heating

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. nVent NUHEAT Membrane is a tile underlayment that can be installed over the entire subfloor for uncoupling, crack isolation and waterproofing purposes and can eliminate the need for a second layer of plywood or concrete backer board in most tile installations. Benefits Reduces the risk of tile cracks due to subfloor movement Acts as tile underlayment Compatible with nVent cable floor heating system Flexible wire spacing and heat output Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Even floor heat distribution No need for a second layer of plywood or concrete backer boards Saves installation time and material costs List of material needed to install Technical Information 25 Sheets per Box | Sheet size: 39'' x 39'' Material: Polypropylene Thickness: 0.22 inches Width: 39 inches Operating Voltage: 120 V, 208 V, and 240 V Power Output: 10-15 watts per square foot depending on wire spacing Maximum Continuous Exposure Temperature: 194 °F (90°C) Heating Cable: 2-wire, grounded, twisted air with PVC outer jacket Cold Lead: 2-wire, 16-18 AWG plus ground braid layer; 10 ft (3m) length Recommended Spacing: 2-3-2 pillar spacing which provides 12 watts/sqft ** If you are installing over a concrete slab and require more heat, we recommend using 2-pillar spacing which produces 15 watts/sqft Documents Brochure Installation Instructions

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information ​Mat Dimension: 6'x4' Amperage: 2.4 amps Power Output: 288 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 120 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description nVent Nuheat Cable is an easy-to-install electric floor heating system that combines installation versatility with advanced new technology. Choose the cable kit that is best suited for the size of the room/area and configure it on-site to provide floor heat in the desired areas of the room. Benefits Heats tile, stone, and laminate/engineered wood floors On-site flexibility Flexible wire spacing and heat output Compatible with nVent Nuheat Membrane Comprehensive selection of sizes to choose from Suitable for wet environments such as showers and steam rooms Redesigned, thinner cold-lead and factory splice New mid-point marker on the heating cable Technical Information Operating Voltage: 120 V Length: 377' Covering Surface: 95 sq. ft. Amperage: 9.7 amps Power Output: 12 - 15 watts per square foot Maximum Ambient Temperature: 194 °F (90°C) Material: Two single conductor Tefzel-coated resistance wires covered by a tin-plated copper braid and then coated with a durable copolymer (PVC) outer jacket Documents Brochure Installation Guide

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. nVent NUHEAT Peel & Stick Membrane (FG0801) enables the installation of uncoupling membrane onto a substrate without the use of thinset, resulting in a 40% time savings versus membranes that require thinset underneath! NOTE: nVent NUHEAT Peel & Stick Membrane is available in 39” x 39” sheets only (25 per box) and cannot be used for waterproofing due to the mortar vents. The installation is done in 4 easy steps. 1- Apply acrylic flooring primer to substrate 2-Press Peel & Stick membrane onto substrate The final permanent bond is created when thinset is applied on top of the membrane when embedding the heating cable. Thinset flows through the mortar vents in the pillars, allowing it to bond to the substrate while maintaining the air gaps required to achieve the same ‘High Performance’ rating on the ANSI A118.12 crack resistance test that the standard nVent NUHEAT Membrane achieves. 3-Route cable throughout heated area (Cable sold separately) 4-Install floor covering (Sold separately) **Cable resistance must be tested before, during and after installation for warranty coverage **All wiring connections should be completed by a certified electrician Benefits Reduces the risk of tile cracks due to subfloor movement Acts as tile underlayment Compatible with nVent cable floor heating system Flexible wire spacing and heat output Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Cleaner and Easier Installation Even floor heat distribution No need for a second layer of plywood or concrete backer boards Saves installation time and material costs Technical Information Part Number: FG0801 Catalog Number: NUMEM250PS Materials: Vented polypropylene sheet with pressure sensitive adhesive and release liver, 0.22in. thick, 840 grams/m² Subfloor Bond: Prep surface with acrylic flooring primer and apply membrane to subfloor; additional mechanical bond is created when thinset passes through mortar vents during floor covering installation. Waterproofing: No Ratings: Robinson Floor Test (ASTM C627): 'Moderate' rating; ANSI A118.12 System Crack Resistance: 'High Performance' rating Max Ambient Temp.: 194°F (90°C) Storage Conditions: Store in a cool and dry place avoiding direct sunlight and heat source. Product Dimensions (LxWxD): 39"x39"x0.22" Product Weight: 1.6lb. Standard Pack: 25 Sheets per box Standard Pack Dimensions (LxWxH): 40"x40"x8" Standard Pack Weight: 45lb. Documents Brochure

Description nVent Nuheat Cable is an easy-to-install electric floor heating system that combines installation versatility with advanced new technology. Choose the cable kit that is best suited for the size of the room/area and configure it on-site to provide floor heat in the desired areas of the room. Benefits Heats tile, stone, and laminate/engineered wood floors On-site flexibility Flexible wire spacing and heat output Compatible with nVent Nuheat Membrane Comprehensive selection of sizes to choose from Suitable for wet environments such as showers and steam rooms Redesigned, thinner cold-lead and factory splice New mid-point marker on the heating cable Technical Information Operating Voltage: 120 V Length: 29' Covering Surface: 8 sq. ft. Amperage: 0.7 amps Power Output: 12 - 15 watts per square foot Maximum Ambient Temperature: 194 °F (90°C) Material: Two single conductor Tefzel-coated resistance wires covered by a tin-plated copper braid and then coated with a durable copolymer (PVC) outer jacket Documents Brochure Installation Guide

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information Dimension: 10'x3' Amperage: 1.5 amps Power Output: 354 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 240 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information ​Mat Dimension: 3'4" x 2'8" Amperage: 0.9 amps Power Output: 107 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 120 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description nVent Nuheat Cable is an easy-to-install electric floor heating system that combines installation versatility with advanced new technology. Choose the cable kit that is best suited for the size of the room/area and configure it on-site to provide floor heat in the desired areas of the room. Benefits Heats tile, stone, and laminate/engineered wood floors On-site flexibility Flexible wire spacing and heat output Compatible with nVent Nuheat Membrane Comprehensive selection of sizes to choose from Suitable for wet environments such as showers and steam rooms Redesigned, thinner cold-lead and factory splice New mid-point marker on the heating cable Technical Information Operating Voltage: 240 V Length: 56' Ampage: 0.7 amps Surface covering: 15 sq. ft. Power Output: 12 - 15 watts per square foot Maximum Ambient Temperature: 194°F (90°C) Material: Two single conductor Tefzel-coated resistance wires covered by a tin-plated copper braid and then coated with a durable copolymer (PVC) outer jacket Documents Brochure Installation Guide

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information ​Mat Dimension: 5' x 2' Amperage: 1.0 amps Power Output: 120 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 120 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information Dimension: 7'x3' (72''x36'') Amperage: 1.1 amps Power Output: 252 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 240 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description nVent Nuheat Cable is an easy-to-install electric floor heating system that combines installation versatility with advanced new technology. Choose the cable kit that is best suited for the size of the room/area and configure it on-site to provide floor heat in the desired areas of the room. Benefits Heats tile, stone, and laminate/engineered wood floors On-site flexibility Flexible wire spacing and heat output Compatible with nVent Nuheat Membrane Comprehensive selection of sizes to choose from Suitable for wet environments such as showers and steam rooms Redesigned, thinner cold-lead and factory splice New mid-point marker on the heating cable Technical Information Operating Voltage: 240 V Length: 358' Amperage: 4.6 amps Surface covering: 90 sq. ft. Power Output: 12 - 15 watts per square foot Maximum Ambient Temperature: 194°F (90°C) Material: Two single conductor Tefzel-coated resistance wires covered by a tin-plated copper braid and then coated with a durable copolymer (PVC) outer jacket Documents Brochure Installation Guide

Description nVent Nuheat Cable is an easy-to-install electric floor heating system that combines installation versatility with advanced new technology. Choose the cable kit that is best suited for the size of the room/area and configure it on-site to provide floor heat in the desired areas of the room. Benefits Heats tile, stone, and laminate/engineered wood floors On-site flexibility Flexible wire spacing and heat output Compatible with nVent Nuheat Membrane Comprehensive selection of sizes to choose from Suitable for wet environments such as showers and steam rooms Redesigned, thinner cold-lead and factory splice New mid-point marker on the heating cable Technical Information Operating Voltage: 240 V Length: 630' Amperage: 8.0 amps Surface covering: 160 sq. ft. Power Output: 12 - 15 watts per square foot Maximum Ambient Temperature: 194°F (90°C) Material: Two single conductor Tefzel-coated resistance wires covered by a tin-plated copper braid and then coated with a durable copolymer (PVC) outer jacket Documents Brochure Installation Guide

Description nVent Nuheat Cable is an easy-to-install electric floor heating system that combines installation versatility with advanced new technology. Choose the cable kit that is best suited for the size of the room/area and configure it on-site to provide floor heat in the desired areas of the room. Benefits Heats tile, stone, and laminate/engineered wood floors On-site flexibility Flexible wire spacing and heat output Compatible with nVent Nuheat Membrane Comprehensive selection of sizes to choose from Suitable for wet environments such as showers and steam rooms Redesigned, thinner cold-lead and factory splice New mid-point marker on the heating cable Technical Information Operating Voltage: 240 V Length: 529' Amperage: 6.8 amps Surface covering: 135 sq. ft. Power Output: 12 - 15 watts per square foot Maximum Ambient Temperature: 194°F (90°C) Material: Two single conductor Tefzel-coated resistance wires covered by a tin-plated copper braid and then coated with a durable copolymer (PVC) outer jacket Documents Brochure Installation Guide

Description nVent Nuheat Cable is an easy-to-install electric floor heating system that combines installation versatility with advanced new technology. Choose the cable kit that is best suited for the size of the room/area and configure it on-site to provide floor heat in the desired areas of the room. Benefits Heats tile, stone, and laminate/engineered wood floors On-site flexibility Flexible wire spacing and heat output Compatible with nVent Nuheat Membrane Comprehensive selection of sizes to choose from Suitable for wet environments such as showers and steam rooms Redesigned, thinner cold-lead and factory splice New mid-point marker on the heating cable Technical Information Operating Voltage: 120 V Length: 474' Covering Surface: 120 sq. ft. Amperage: 12.2 amps Power Output: 12 - 15 watts per square foot Maximum Ambient Temperature: 194 °F (90°C) Material: Two single conductor Tefzel-coated resistance wires covered by a tin-plated copper braid and then coated with a durable copolymer (PVC) outer jacket Documents Brochure Installation Guide

Description nVent Nuheat Cable is an easy-to-install electric floor heating system that combines installation versatility with advanced new technology. Choose the cable kit that is best suited for the size of the room/area and configure it on-site to provide floor heat in the desired areas of the room. Benefits Heats tile, stone, and laminate/engineered wood floors On-site flexibility Flexible wire spacing and heat output Compatible with nVent Nuheat Membrane Comprehensive selection of sizes to choose from Suitable for wet environments such as showers and steam rooms Redesigned, thinner cold-lead and factory splice New mid-point marker on the heating cable Technical Information Operating Voltage: 120 V Length: 47' Covering Surface: 12 sq. ft. Amperage: 1.2 amps Power Output: 12 - 15 watts per square foot Maximum Ambient Temperature: 194 °F (90°C) Material: Two single conductor Tefzel-coated resistance wires covered by a tin-plated copper braid and then coated with a durable copolymer (PVC) outer jacket Documents Brochure Installation Guide

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information Dimension: 10'x3.5' Amperage: 1.7 amps Power Output: 413 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 240 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information Dimension: 7'x3.5' Amperage: 1.2 amps Power Output: 294 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 240 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information Dimension: 6'x4' Amperage: 1.2 amps Power Output: 288 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 240 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information ​Mat Dimension: 9'x4' Amperage: 3.6 amps Power Output: 432 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 120 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description nVent Nuheat Cable is an easy-to-install electric floor heating system that combines installation versatility with advanced new technology. Choose the cable kit that is best suited for the size of the room/area and configure it on-site to provide floor heat in the desired areas of the room. Benefits Heats tile, stone, and laminate/engineered wood floors On-site flexibility Flexible wire spacing and heat output Compatible with nVent Nuheat Membrane Comprehensive selection of sizes to choose from Suitable for wet environments such as showers and steam rooms Redesigned, thinner cold-lead and factory splice New mid-point marker on the heating cable Technical Information Operating Voltage: 240 V Length: 80' Ampage: 0.9 amps Surface covering: 20 sq. ft. Power Output: 12 - 15 watts per square foot Maximum Ambient Temperature: 194°F (90°C) Material: Two single conductor Tefzel-coated resistance wires covered by a tin-plated copper braid and then coated with a durable copolymer (PVC) outer jacket Documents Brochure Installation Guide

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information Dimension: 5'x3.5' Amperage: 0.9 amps Power Output: 210 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 240 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information Dimension: 5'x3' Amperage: 0.8 amps Power Output: 180 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 240 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information ​Mat Dimension: 9' x 3' Amperage: 2.7 amps Power Output: 324 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 120 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information ​Mat Dimension: 3'4" x 2'3" Amperage: 0.8 amps Power Output: 90 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 120 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install

Description ***Traditional hardwood is typically not recommended to be installed over an electric floor heating system because the repeated heating and cooling cycles may damage the wood. Standard Mats are the thinnest and easiest to install. Standard Mats are only 1/8” thick and eliminate the need to configure the heating wires during installation. Standard Mats come in various dimensions. Simply pick the size of the mat(s) that fits the desired heating area. Because the heating wire is embedded in the Standard Mat and does not need to be configured during installation, the heat coverage is guaranteed to be consistent throughout the desired heating area. Benefits Easy to install Error-Free Reduces installation time Does not raise floor height Comprehensive selection of sizes to choose from Nuheat is approved for installation under tile, stone, marble, laminate, engineered wood, and luxury vinyl flooring Technical Information ​Mat Dimension: 6'x3.5' Amperage: 2.1 amps Power Output: 252 watts Material: Consist of a single-conductor tinned copper braided heating wire sandwiched in a pre-configured pattern between durable, two porous layers of fabric ​Operating Voltage: 120 V ​Maximum Continuous Exposure Temperature: 194°F (90°C) ​Heating Cable: Single wire with ground braid outer layer ​Cold Lead: 2-wire, 18 AWG plus ground braid layer; 10 ft (3m) length Documents Brochure Installation Instructions Mat Shower Installation Instructions List of material needed to install